$705.29
Engineered to be an inexpensive solution for the hydroponic or greenhouse grower to maintain the ideal nutrient solution concentration level in the reservoir tank. The HI981413 GroLine Nutrient Dosing System is a complete solution with advanced process controller and a built in chemical dosing pump. Simply insert the probe and injection valve in-line with the re-circulation pump and supply the stock fertilizer to be dosed.
HI981413 Nutrient Dosing System is designed to maintain the concentration of fertilizer nutrient solution used in hydroponics and irrigation water. The HI981413 uses an amperometric conductivity sensor to measure the amount of fertilizer in the solution. The meter can be programmed to display results as EC (electrical conductivity) or as TDS (total dissolved solids). The EC results are displayed as mS/cm while TDS is displayed as ppm with a selectable conversion factor from 0.45 to 0.99. The HI981413 was developed as a cost-effective solution for the horticulturist to maintain the ideal fertilizer concentrations by placing the probe and injection valve in-line with the re-circulation pump to provide the chemical to be dosed.
The HI981413 features a multi-colored LCD to show the status of the pool controller. The display is green during normal opperation, yellow if the control is not enabled, or flashes red when an alarm is triggered.
Both conductivity or TDS and temperature are displayed with status icons that show when the pump is dosing and the control mode status.
Hanna controllers allow users to enable or disable the low and high-level alarms for EC/TDS. When an alarm is activated, all dosing will stop. For added safety, the alarm system also offers overdosing protection in that if the set point value is not corrected within a programmed time interval then the meter will go into alarm status.
Adjustable Flow Rate
The flow rate from the dosing pumps is adjustable from 0.5 to 3.5L/h. Larger bodies of water require more chemical to be dosed than smaller ones in per unit of time. The adjustable flow rate, like the proportional band, allows for better control in maintaining a desired set point .
Automatic Proportional Pump Control
The peristaltic dosing pump can be controlled by simple on/off or more advanced proportional control which helps prevents overshooting of the set point. When using proportional control the flow rate that is programmed, will be impacted by the proportional band used. The closer the reading is to the set point the longer it takes for the peristaltic pump to complete one revolution. If the reading is outside the proportional band then the amount of time it takes to complete one revolution is based on the flow rate programmed.
Acid Tank Level/Flow Switch Input
The BL100 allows for a connection to an optional level controller or flow switch. This input can be used to disable the dosing pump when there is no chemical left in the reservoir tank or there is no flow due to the pump being turned off.
The HI981413 features a peristaltic dosing pump that is superior to diaphragm versions due to the ability to self-prime when there is no liquid in the uptake line.
The brushless motor does not have nay gears or brushes that can wear out. A brushless design provides for a long life and little maintenance. The compact stepper motor allows for very precision control over the dosing of the chemical.
The industrial grade peristaltic tubing is chemical resistant and provides for a relatively long-life. As tubing stretches over time it can be easily replaced. No special tools required.
The HI981413 is available in multiple configurations including a meter only, meter and probe, and
a complete package that includes bypass loop
and panel mounted flow through cell. All models include aspiration tubing with filter and dispensing tubing with injection valve.
The HI981413 uses the HI30003 probe that incorporates both conductivity and temperature sensors and connects to the controller with a single waterproof Quick Connect DIN connector.
The ABS body of the probe has a 1/2” threaded fitting for insertion to an in-line “T” fitting or the flow cell. The back end part of the probe has 3/4” NPT threads for submersion/ tank mounting. The probe body has a hex fitting for tightening snuggly with a wrench. .
| SKU | HI981413 |
| Name | Groline Nutrient Dosing System-HI981413 |
| EC Range | 0.00 to 10.00 mS/cm |
| EC Resolution | 0.01 mS/cm |
| EC Accuracy | 2% F.S. |
| EC Calibration | User calibration: automatic, one-point with standard solution (1.41 or 5.00 mS/cm) Process calibration: single point, adjustable (±0.50 mS/cm around measured value) The corresponding value in TDS, depends on TDS factor used |
| TDS Range | 0 to 9900 ppm, depends on TDS factor i.e. with TDS factor 0.5, range 50 to 5000 ppm with TDS factor 0.7, range 70 to 7000 ppm |
| TDS Resolution | 1 ppm |
| TDS Accuracy | 2% F.S. |
| EC/TDS Temperature Compensation | automatic |
| Temperature Correction Coefficient | β can be set from 0%/°C to 2.4%/°C; default is 1.9%/°C |
| EC to TDS Conversion Factor | TDS factor selectable from 0.45 to 0.99 |
| EC/TDS Dosing Set Point | on/off control using adjustable set point (0.10 to 10.00 mS/cm; 45 to 9900 ppm, depends on TDS factor) proportional control 0.10 to 10.00 mS/cm; 45 to 9900 ppm, depends on TDS factor |
| EC/TDS Proportional Band | 0.05 to 1.00 mS/cm; 23 to 990 ppm, depends on TDS factor |
| EC/TDS Hysteresis Band | 0.05 to 0.50 mS/cm; 23 to 495 ppm, depends on TDS factor |
| Temperature Range | -5.0 to 105.0°C; 23.0 to 221.0°F* |
| Temperature Resolution | 0.1°C; 0.1°F |
| Temperature Accuracy | ±0.5°C; 1°F |
| Dosing Control | startup delay timer at power-on (0 to 600 sec.) Pump flow control 0.5 to 3.5 Liter/hour (0.13 to 0.92 Gallon/hour) and maximum output pressure 1 atm (14 psi) manual control for pump priming (defined in setup) |
| Alarm Relay Set Point | triggered after 5 sec. if the controller records consecutive readings over or under threshold values |
| Over Dosing Control | overtime protection (1 to 180 m in. or Off) |
| Digital Input Signal | galvanically isolated external switches can be attached to stop the pump and activate the alarm (low reagent level) when the switch is open and level alarm is configured in Setup |
| Backlight | intuitive alarm system, using red, yellow and green color coded backlight |
| Power Consumption | 15 VA |
| Enclosure | wall mounted, built-in pump |
| Power Supply | 100 - 240 Vac, 50/60 Hz |
| Environment | 0 to 50°C (32 to 122°F); RH max. 95% non-condensing |
| IP Rating | IP65 |
| Dimensions | 90 x 142 x 80 mm (3.5 x 5.6 x 1.8 in.) |
| Weight | 908 g (36 oz.) |
HI981413-00 is supplied with HI981413 controller, HI30033 EC/TDS/temperature probe, HI7031-012 conductivity calibration solution (1413 µS/cm - 120 ml), plastic beaker, power connection cable, instruction manual and quality certificates for instrument and probe.
HI981413-10 (with in-line mounting kit) is supplied with HI981413 controller, HI30033 EC/TDS/temperature probe, controller aspiration filter, controller injector, 1/2” thread, saddle for Ø 50 mm pipe (2), PVC aspiration tubing (flexible) (5 m), PE rigid dispensing tubing (5 m), HI7031-012 conductivity calibration solution (1413 µS/cm - 120 ml), plastic beaker, power connection cable, instruction manual and quality certificates for instrument and probe.
HI981413-20 (with flow-cell mounting kit) is supplied with HI981413 controller, HI30033 pH/temperature probe, flow cell for HI981413, mounting panel assembly for HI981413, controller aspiration filter, controller injector, 1/2” thread, saddle for Ø 50 mm pipe (3), PVC aspiration tubing (flexible) (5 m), PE rigid dispensing tubing (15 m), barbed tubing adapter 1/2” - 6 mm with racord (2), flow cell valves (2), HI7031-012 conductivity calibration solution (1413 µS/cm - 120 ml), plastic beaker, power connection cable, instruction manual and quality certificates for instrument and probe.
All prices are inclusive of GST and not all items are stock items, if you require an immediate solution please send an email to sales@hannainst.com.au or call us on (03) 9769 0666.
Free standard delivery: We offer free delivery within Australia on orders over $100, typically arriving within 5 to 7 days. Delivery times may vary depending on the courier service and the recipient's location. Free shipping is not available with other offers or discounts.
Same-day despatch: Place your order before 1 PM Monday to Friday for same-day despatch. Delivery times may vary depending on the courier service and the recipient's location. Subject to stock availability.
Please note that we do not offer shipping to PO Box addresses.
| Weight | 2.27 kg |
|---|---|
| Parameter | Conductivity/TDS |
| EC Accuracy | 2% F.S. |
| EC Calibration | adjustable (±0.50 mS/cm around measured value)The corresponding value in TDS, depends on TDS factor used, one-point with standard solution (1.41 or 5.00 mS/cm) Process calibration: single point, User calibration: automatic |
| EC Range | 0.00 to 10.00 mS/cm |
| EC Resolution | 0.01 mS/cm |
| TDS Accuracy | 2% F.S. |
| TDS Range | 0 to 9900 ppm, depends on TDS factor i.e. with TDS factor 0.5, range 50 to 5000 ppmwith TDS factor 0.7, range 70 to 7000 ppm |
| TDS Resolution | 1 ppm |
| Temperature Accuracy | ±0.5°C; 1°F |
| Temperature Range | -5.0 to 105.0°C; 23.0 to 221.0°F* |
To empower customers to achieve quality
by supplying intuitive, accurate, and reliable analytical instruments with exceptional customer service and value.
We take pride in every product we build. From an original idea, to a completed product ready for testing. We oversee every aspect of the manufacturing process. It is this level of attention to detail that sets us apart.
To empower customers to achieve quality by supplying intuitive, accurate, and reliable analytical instruments with exceptional customer service and value.
We take pride in every product we build. From an original idea, to a completed product ready for testing. We oversee every aspect of the manufacturing process. It is this level of attention to detail that sets us apart.
To empower customers to achieve quality by supplying intuitive, accurate, and reliable analytical instruments with exceptional customer service and value.
We take pride in every product we build. From an original idea, to a completed product ready for testing. We oversee every aspect of the manufacturing process. It is this level of attention to detail that sets us apart.
